Exploring Plumbing Fundamentals When You Install a Bathtub
Exploring Plumbing Fundamentals When You Install a Bathtub
Blog Article
The publisher is making several good points on A Step-by-Step Guide to Installing a Bathtub as a whole in the article down below.
Setting up a tub isn't specifically brain surgery, however it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is easily easily accessible, the task can move immediately; if you need to open up a wall to remove the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have certified yourself for the work as well as fit trying it. Rather than hiring a contractor to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will certainly help you set up a brand-new bath tub in your restroom if you have actually already acquired a brand-new tub as well as do not need to change the arrangement of your previous water system pipelines.
Your tools and product list ought to comprise the following:
Planning for the Installment
First of all, the supporting framework supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome due to the restricted accessibility that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the furthest flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Load the bath tub as well as additionally check the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least once as this will settle it right into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in complications with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealer can crack rather early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the market. It is recommended to fit the ceramic tiles making use of waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our piece about How to Install a Bathtub. Thank you for taking time to read through our piece. Do you know about someone else who is sincerely interested in How to Install a Bathtub? Be sure promote it. Thanks for your time spent reading it.
Book Maintenance Report this page